dynoed (mustang load bearing) my m240i jb4 map 4/5 on e30

E63M6_G42M240i · 05-04-2023, 11:14 AM

dyno run

heelsmj · 05-07-2023, 10:28 PM

What did they charge you for a dyno run?

E63M6_G42M240i · 05-07-2023, 10:33 PM

Quote:

Originally Posted by heelsmj

What did they charge you for a dyno run?

$150 for two pulls

AWcoupe · 05-08-2023, 12:34 AM

Did you ever do a stock baseline on pump gas? This thing definitely feels like it makes more than 382 hp stock at the crank according to my butt meter. Melbourne looks great!

E63M6_G42M240i · 05-08-2023, 12:49 AM

Quote:

Originally Posted by AWcoupe

Did you ever do a stock baseline on pump gas? This thing definitely feels like it makes more than 382 hp stock at the crank according to my butt meter. Melbourne looks great!

No I havent but keep in mind load bearing dynos (mustang) are typically less than inertia based (dynojet). I think I saw one at 360 ish on a load bearing (car wow).

XC3LLR8 · 05-08-2023, 08:53 AM

So 432 WHP and 408 TQ at 20.0 PSI - not bad!

I've read the rule-of-thumb is approximately a 7% increase in HP for each additional PSI, so if you hit the 22 PSI target of map 5 that may put you around 490 WHP

E63M6_G42M240i · 05-08-2023, 10:51 AM

Quote:

Originally Posted by XC3LLR8

So 432 WHP and 408 TQ at 20.0 PSI - not bad!

I've read the rule-of-thumb is approximately a 7% increase in HP for each additional PSI, so if you hit the 22 PSI target of map 5 that may put you around 490 WHP

That would be awesome. Have to make sure the fueling will support it first. If that’s maxed out, then it doesn’t really matter. There’s only so much the JB4 can do. I’m going to do more data logging this week and have Burger figure it out, perhaps in Map 6.

XC3LLR8 · 05-08-2023, 11:04 AM

Quote:

Originally Posted by E63M6_G42M240i

That would be awesome. Have to make sure the fueling will support it first. If that’s maxed out, then it doesn’t really matter. There’s only so much the JB4 can do. I’m going to do more data logging this week and have Burger figure it out, perhaps in Map 6.

Aside from an intake I have the same setup as you. Regardless what the numbers end up being this car is stupid-fast for the street.

E63M6_G42M240i · 05-08-2023, 11:16 AM

Quote:

Originally Posted by XC3LLR8

Aside from an intake I have the same setup as you. Regardless what the numbers end up being this car is stupid-fast for the street.

Yup, the power delivery is so nice too. Easy to drive fast!

05-04-2023, 11:14 AM	#1
E63M6_G42M240i Lieutenant 1081 Rep 652 Posts Drives: 2024 TR G80 M3CX Join Date: Jul 2022 Location: Orange County, CA, USA iTrader: (0) Garage List 2024 G80 M3 Comp Xd ... [10.00]	dynoed (mustang load bearing) my m240i jb4 map 4/5 on e30 dyno run Attached Images
	Appreciate 5 heelsmj359.50 ZM240i177.00 XC3LLR82089.00 viperx100682.00 lithe32.50 Tweet Quote

05-07-2023, 10:28 PM	#2
heelsmj Second Lieutenant 360 Rep 265 Posts Drives: 2023 M240 Xdrive Retired M340 Join Date: May 2020 Location: South Florida iTrader: (0)	What did they charge you for a dyno run?
	Appreciate 0 Quote

05-08-2023, 12:34 AM	#4
AWcoupe Second Lieutenant 170 Rep 201 Posts Drives: 2023 BMW 240i xDrive Join Date: Sep 2012 Location: Bridgeport CT iTrader: (0) Garage List 2023 BMW M240 [0.00] 2015 BMW 235xi [0.00]	Did you ever do a stock baseline on pump gas? This thing definitely feels like it makes more than 382 hp stock at the crank according to my butt meter. Melbourne looks great! __________________ 2023 BMW M240i 2015 BMW 235xi Alpine White, Coral Red Dakota.Traded 2009 BMW 328xi Alpine White-Traded
	Appreciate 0 Quote

05-08-2023, 08:53 AM	#6
XC3LLR8 Banned 2089 Rep 1,559 Posts Drives: Super73 Join Date: Jan 2022 Location: Keller, TX iTrader: (0)	So 432 WHP and 408 TQ at 20.0 PSI - not bad! I've read the rule-of-thumb is approximately a 7% increase in HP for each additional PSI, so if you hit the 22 PSI target of map 5 that may put you around 490 WHP
	Appreciate 0 Quote

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search