[@indiv.official]

with RED

[fluffhead]

Originally Posted by a358970751

Same here , waiting for gloss black ABS plastic inlet . Not fans of carbon fiber

Will wait for Gloss Black as well

[fluffhead]

Originally Posted by @indiv.official

with RED

Any plans on doing something similar for the grille? It would be great not to have to remove the bumper. I would also want gloss black though

[JABCAT]

Originally Posted by fluffhead

Any plans on doing something similar for the grille? It would be great not to have to remove the bumper. I would also want gloss black though

You have to remove the front fascia to remove the oem grille, no way around it.

[fluffhead]

Originally Posted by JABCAT

You have to remove the front fascia to remove the oem grille, no way around it.

I was asking if they can make a grille that goes over the OEM, just like the inlets.

I see what it takes to change out the grilles and it's not something I feel comfortable doing.

[@indiv.official]

Originally Posted by fluffhead

I was asking if they can make a grille that goes over the OEM, just like the inlets.

I see what it takes to change out the grilles and it's not something I feel comfortable doing.

let me see what can we do for it

[@indiv.official]

Matte black M2

[@indiv.official]

indiv carbon inlet

[@indiv.official]

From Japan

[@indiv.official]

Red M2

[mdrobc13]

Originally Posted by FKDTM2

From Canada 🤝

Very nice….what front bumper lip do you have installed on your car? Very complimentary look.

[ourlee]

Originally Posted by Sleeper

Inlets arrived from iND today. Well packaged, and overall impressed with the quality and finish. There is a double layer of 3M VHB double-sided tape installed (stacked). I assume the stacked tape is to help with snug fitment.

Will have these PPF’ed and coated, and then installed.

GREAT pics

[Sleeper]

Originally Posted by ourlee

GREAT pics

Thank you!

I meant to update in this thread a while back, but I found the 3M tape coverage from INDIV very much inadequate for the job. Adding to the challenge was sticking these to freshly ceramic coated PPF film. So maybe on non-coated paint (vs coated PPF), the usual 3M they apply would be fine.

For my inlets specifically, I added another fresh layer of 3M a full 360* around the front of the inlet (going over top of what they applied), and along the back of the inlet on the top surface. I also had to IPA wipe the areas a million times to get it to actually bond.

End result is top notch though.

[ourlee]

I really need to stay off ind DAMN

[@indiv.official]

Originally Posted by Sleeper

Thank you!

I meant to update in this thread a while back, but I found the 3M tape coverage from INDIV very much inadequate for the job. Adding to the challenge was sticking these to freshly ceramic coated PPF film. So maybe on non-coated paint (vs coated PPF), the usual 3M they apply would be fine.

For my inlets specifically, I added another fresh layer of 3M a full 360* around the front of the inlet (going over top of what they applied), and along the back of the inlet on the top surface. I also had to IPA wipe the areas a million times to get it to actually bond.

End result is top notch though.

yes you are right. for ppf surface, it will not working😢😢😢because of ppf coating..

[@indiv.official]

From Semashow !!!!

[curtdragon]

I need someone to make ones that go up and down to match the Adro front grill

[@indiv.official]

INDIV inlet + double slat grill !!

[Zirenz2006]

I have a barely used pair for sale if anyone is interested, PM me.

[Ronin76]

It’s weird, when I put my address in it says that it’s not valid. I tried putting my mom’s addess in and the same thing.