[jessejericho]

Turner Motorsports have released their front splitter, looks really nice!

https://www.turnermotorsport.com/p-3...ber-front-lip/

[Orange fever]

Pick this up at European Auto Source, EAS
Lightweight Performance Front Splitter -
https://g87.bimmerpost.com/forums/sh....php?t=2082113
And loved it ///

[Whytar]

I went with the Aeroflow Dynamics [pictured, but not my car]. Not because of it's lower price point, but because of it's simplicity, and the fact it doesn't lower the clearance height quite as much as some of the others.

[ourlee]

Originally Posted by Orange fever

Pick this up at European Auto Source, EAS
Lightweight Performance Front Splitter -
https://g87.bimmerpost.com/forums/sh....php?t=2082113
And loved it ///

Mine just arrived. My wife is “wtaf” you don’t even have the car yet lol

[Ehloo]

i am running the aero front lip. It’s good for the money and like the simplicity of the design but it’s not stiff at all and flexes.

the turner piece looks very similar and carbon. with the discount it’s worth consideration

Originally Posted by Whytar

I went with the Aeroflow Dynamics [pictured, but not my car]. Not because of its lower price point, but because of its simplicity, and the fact it doesn't lower the clearance height quite as much as some of the others.

[nicoG87]

Originally Posted by Ehloo

i am running the aero front lip. It’s good for the money and like the simplicity of the design but it’s not stiff at all and flexes.

the turner piece looks very similar and carbon. with the discount it’s worth consideration

i have the same concern about the flex in that splitter.

turner looks great but discount is sadly gone.

[tylerdurdem]

Been a while since I checked, is there an Alpha N GT replica in gloss black at this point? It's the best looking IMO, but that price is a bit nutty.

[JABCAT]

Originally Posted by Ehloo

i am running the aero front lip. It’s good for the money and like the simplicity of the design but it’s not stiff at all and flexes.

the turner piece looks very similar and carbon. with the discount it’s worth consideration

Under what circumstances are you seeing it flex & did you use mounting tape & the self-tapping screws? Mine seems pretty solid up front, and while not as stiff as the carbon fiber splitter on my other car, the Aeroflow appears just as stiff as the MPerformance front splitter I had on my 3-series (was also abs plastic).

[Ehloo]

full disclosure i didn’t use any see tap screws, just oem mounting points and 3m vhb

it’s the middle section that protrudes, i didn’t fee the extra screws would do much. the plastic is not stiff and a bit flexible.

Originally Posted by JABCAT

Under what circumstances are you seeing it flex & did you use mounting tape & the self-tapping screws? Mine seems pretty solid up front, and while not as stiff as the carbon fiber splitter on my other car, the Aeroflow appears just as stiff as the MPerformance front splitter I had on my 3-series (was also abs plastic).

[jhstjh]

Originally Posted by Ehloo

full disclosure i didn’t use any see tap screws, just oem mounting points and 3m vhb

it’s the middle section that protrudes, i didn’t fee the extra screws would do much. the plastic is not stiff and a bit flexible.

I installed it today and have the same feeling. The side pieces are quite sturdy (and I used the self tapping screws) but the center piece flexes so much...hope it can last long enough 🤞

[JABCAT]

Originally Posted by jhstjh

I installed it today and have the same feeling. The side pieces are quite sturdy (and I used the self tapping screws) but the center piece flexes so much...hope it can last long enough 🤞

Did you use the tape & screws? The center section on mine doesn't seem to flex at all : I'll also give props to their paint as I replaced the center section and haven't had ppf installed on it after replacement. I drive a lot of miles each week on the interstate, and have a lot of marks in my front end ppf to show for it. So far (knock on wood) no chips in the paint of the unprotected center section.

[jmg]

Originally Posted by Orange fever

Pick this up at European Auto Source, EAS
Lightweight Performance Front Splitter -
https://g87.bimmerpost.com/forums/sh....php?t=2082113
And loved it ///

Looks good! I'm still debating this or the Turners. I like the Turners, but my driveway is merciless, and with the corners sticking out, my extreme sideways approach scrapes most lips. The Lightweight doesn't extend in the corners as much, so it will less likely scrape.