[mike@x-ph.com]

Originally Posted by NewToM

Thanks sir! Excited to get it.

[E63M6_G42M240i]

Originally Posted by mike@x-ph.com

Mike what version of this midpipe do you get if you have a MAD axleback?

[mike@x-ph.com]

Originally Posted by E63M6_G42M240i

Mike what version of this midpipe do you get if you have a MAD axleback?

Milltek

Milltek and MAD both use 3" connection versus the stock which is a 2.75" connection

[MikeyP]

So, is the only difference between the Milltek SSXBM1329 midpipe (is this whats considered equal length?) and the Milltek SSXBM1331 midpipe (X pipe) just the sound?

[mike@x-ph.com]

Originally Posted by MikeyP

So, is the only difference between the Milltek SSXBM1329 midpipe (is this whats considered equal length?) and the Milltek SSXBM1331 midpipe (X pipe) just the sound?

one uses the X-pipe, one does not. the only difference between the 2 is the sound on high RPM

[wrh3]

I just installed the Milltek single mid pipe and MAD exhaust over the weekend, I'll post some pics and vids when I get home later this week. I had to make extension extensions for my Quickjacks since the jack points have been pushed out to the far corners of the car but they worked well enough. 😆

[mike@x-ph.com]

Originally Posted by wrh3

I just installed the Milltek single mid pipe and MAD exhaust over the weekend, I'll post some pics and vids when I get home later this week. I had to make extension extensions for my Quickjacks since the jack points have been pushed out to the far corners of the car but they worked well enough. 😆

how does it sound?

[wrh3]

Originally Posted by mike@x-ph.com

how does it sound?

I'm happy with it :

Just a quick clip I had on my phone.

Just a bit louder and with no drone in normal mode, aggressive but not overly so in sport mode.

[mike@x-ph.com]

Originally Posted by MikeyP

So, is the only difference between the Milltek SSXBM1329 midpipe (is this whats considered equal length?) and the Milltek SSXBM1331 midpipe (X pipe) just the sound?

Both of these options are single midpipe, one with an X-pipe and one without

equal length would be what active autowerke offers

[NewToM]

Mine is still in my office so sad seeing it everyday! Just got to find time for install.

[L3G0TS]

Originally Posted by wrh3

I'm happy with it : https://youtu.be/mLbNytR6Ffw?feature=shared

Just a quick clip I had on my phone.

Just a bit louder and with no drone in normal mode, aggressive but not overly so in sport mode.

Sounds good, pretty tame to me compared to the normal single setup from Miltek seems, do you have a sound clip where you can rev a little bit higher?

[mike@x-ph.com]

Originally Posted by NewToM

Mine is still in my office so sad seeing it everyday! Just got to find time for install.

[NewToM]

Originally Posted by mike@x-ph.com

End of the year and all that!

[MikeyP]

I have the midpipe on order from Mike (thanks again, excellent doing bidness with you.) Do you have to cut the factory pipe in the rear? If so, can you use the dimples for a cut? Or do I have to hold the pipe up there and make a mark? Wondering how many hands I need to employee.

[mike@x-ph.com]

Originally Posted by MikeyP

I have the midpipe on order from Mike (thanks again, excellent doing bidness with you.) Do you have to cut the factory pipe in the rear? If so, can you use the dimples for a cut? Or do I have to hold the pipe up there and make a mark? Wondering how many hands I need to employee.

Thank you for the support

2 can get the job done, 3 makes it a lot easier

[MikeyP]

Anyone with any info on the cutting?

[JPattyG87]

Originally Posted by mike@x-ph.com

one uses the X-pipe, one does not. the only difference between the 2 is the sound on high RPM

Which one is higher in the rpm’s and which one not I’m trying to decide between the two and place an order with you lol no Rhyme intended

[mike@x-ph.com]

Originally Posted by JPattyG87

Which one is higher in the rpm’s and which one not I’m trying to decide between the two and place an order with you lol no Rhyme intended

the X pipe has a louder tone on higher RPM

[nightfire]

Any drone with the 4" midpipe since its not resonated?

[mike@x-ph.com]

Originally Posted by nightfire

Any drone with the 4" midpipe since its not resonated?

no drone as long as everything else is stock

[WWM3]

This is an educational thread. It seems that Mike has both the X and non X versions of the 4'' Milltek available. EAS sells the X version. I have yet to find a clip of the X version with the stock rear section.

[mike@x-ph.com]

Originally Posted by WWM3

This is an educational thread. It seems that Mike has both the X and non X versions of the 4'' Milltek available. EAS sells the X version. I have yet to find a clip of the X version with the stock rear section.

Correct we have both versions in stock and ready to ship, 24 business hours max for orders to ship out

Its not the same but lots of examples in the G80 and G82, the X-pipe version is more popular than the regular one on that platform.

if you are not sure, get the regular version