[youloze]

Originally Posted by DrewNewM2

Day to day I’m scraping my steep driveway if I forget to adjust my approach or exit angle. Speed bumps, parking lot ingresses and egresses all scrapes.

I scared the shit out of some guy when I was pulling into a bagel store lot last week. Loud crunching scrape. He practically jumped out of his shoes. I think he yelled in fear too. Did I care? Nope. I have a cheap lip.

I'll say, it doesn't seem like the Maxton lip would be very durable because of the design, but it can take a beating within reason. I'm very well versed at driving lowered cars with lips, but sometimes you just can't get around an occasional scrape. Other than some slight scrapes on the bottom the lip remains in tact! For $250 I'll take it!

[DrewNewM2]

Originally Posted by youloze

I'll say, it doesn't seem like the Maxton lip would be very durable because of the design, but it can take a beating within reason. I'm very well versed at driving lowered cars with lips, but sometimes you just can't get around an occasional scrape. Other than some slight scrapes on the bottom the lip remains in tact! For $250 I'll take it!

Yeah mine is still good as well. Some rough bottom edge you can feel with your hand, but you can’t see it.

[BroDoze]

Is the finish good enough that it doesn’t need to be gloss black vinyl’s or PPF’d?

[youloze]

Originally Posted by BroDoze

Is the finish good enough that it doesn’t need to be gloss black vinyl’s or PPF’d?

The finish on mine is a gloss black. It's a nice finish for the price. If you want ultimate protection you could PPF it, but in my opinion it's not worth the extra cost based on how much you can just buy a new one for.

[JABCAT]

Originally Posted by Carefree

I was hoping for an accompanying Z06 story.
They all run together.

The front splitter on my Z06 is $2k & the side skirts are $2.6k. Didn't want to leave you hangin.

[youloze]

Originally Posted by JABCAT

The front splitter on my Z06 is $2k & the side skirts are $2.6k. Didn't want to leave you hangin.

I had the Z07 package on my C7 Z06, so carbon everything. One of the reasons I went with Maxton on the M2. I got a small chip in the Z06 carbon lip and it sucked. Didn't want to go through the same on the M2.

[JABCAT]

Originally Posted by DrewNewM2

Of course they’re cheaply made. It’s a $200 lip and should be considered somewhat disposable on a lowered car. I think that’s the point. I scrape mine so often I couldn’t imagine putting anything valuable that low on the car. Side skirts too. I hope they last a year or two. They look decent and fit decent so I’m good. Now the rear or anything else higher up in the car, I would spend a little more for something hopefully of higher quality but there are so many vendors selling carbon pieces, who knows what’s quality or not.

There's cheap, and then there's cheap, cheap. I'll put the Maxton in the cheap, cheap category. If the parts were $100, it would make sense, but even at $250 they're way over priced. I had pieces from Ikon Motorsports on my 3-series that were cheap ($100-$150) that were near direct copies of BMW pieces. Really good pieces for the cost, I was pleasantly surprised. I also had the oem front splitter from BMW and at $700 the fitment was worse than the $150 part & quality was indistinguishable.

[NewToM]

Worried that my lip will be gone shortly after install of HAS…

[Carefree]

Originally Posted by NewToM

Worried that my lip will be gone shortly after install of HAS…

Totaling up all the factory options (including HAS) and aftermarket mods in regards to my G87 purchase, the front lip is my only regret. I can live with that batting average.

YMMV

[thinking]

I've had the Street Pro V2 installed for a while now, and it's been great. The splitter is stable, with a flat bottom, and has a more subtle design compared to other Maxton splitters, except for the Street Pro V1. You might also want to check out the KG splitter from Kies, which is around $400.

[JABCAT]

For anyone thinking about the Maxton parts & not 100% sure you'll want to install them.

$100 shipping to me (non-refundable)
$295 to ship back to them in IL from TX (non-refundable)
10% restocking fee ($62)

[DCC]

Originally Posted by JABCAT

For anyone thinking about the Maxton parts & not 100% sure you'll want to install them.

$100 shipping to me (non-refundable)
$295 to ship back to them in IL from TX (non-refundable)
10% restocking fee ($62)

Thats rough... almost 500.00 gone just to find out the quality of these items.
😞

[NewToM]

Originally Posted by JABCAT

For anyone thinking about the Maxton parts & not 100% sure you'll want to install them.

$100 shipping to me (non-refundable)
$295 to ship back to them in IL from TX (non-refundable)
10% restocking fee ($62)

Why is it 3x as much to ship back?

EDIT: to be clear, that sucks sorry sir.

[JABCAT]

Originally Posted by NewToM

Why is it 3x as much to ship back?

EDIT: to be clear, that sucks sorry sir.

That was with my wife's corp account which added email tracking ($33/box x 3 boxes). Size of the boxes drives up the cost. I'm assuming Dash Imports (Maxton USA) gets a break on shipping.

[Ehloo]

could you post some more pics of your street pro splitter. i was considering this style hoping it wouldn’t be as aggressive and low as their other offerings. how much lower did it drop your front? i am pretty low on AST HAS

maxton marketing is pretty crappy. black car with black parts. really hard to tell what’s going on.

Originally Posted by thinking

I've had the Street Pro V2 installed for a while now, and it's been great. The splitter is stable, with a flat bottom, and has a more subtle design compared to other Maxton splitters, except for the Street Pro V1. You might also want to check out the KG splitter from Kies, which is around $400.

[thinking]

Sure, these are the images I have at the moment. I hope they help somewhat

Originally Posted by Ehloo

could you post some more pics of your street pro splitter.

True..

Originally Posted by Ehloo

maxton marketing is pretty crappy. black car with black parts. really hard to tell what’s going on.