Zunsport oil cooler mesh

motorknut · 06-16-2024, 10:46 PM

So I picked up the zunsport mesh for the underside, and a friend helped with the DIY.

He pointed out that the mount bracket of the mesh doesn't sit flush with the OEM mount point on the car plate. he suggested getting some washers to make the bracket sit flush, and get an extended screw to replace the OEM 10mm hex bolt.

(photo where he's pointing how the other hex bolts sit flush in the mount point, versus the one installed over the mesh bracket.)

Anyone else considered some tweaks to the install? i'm a little concerned how sturdy it is with the original install instructions/parts as per Zunsport.

JABCAT · 06-17-2024, 07:03 AM

I've had mine installed for nearly 9k miles. The only change I made was a little bit larger screws for the rear.

http://https://g87.bimmerpost.com/fo...+cooler+grille

Grace · 06-17-2024, 07:16 AM

You can do as I (and others ) have done and tuck the mounting tab under the plastic rather than over like the instructions have it.

DSTR · 06-17-2024, 08:41 AM

Quote:

Originally Posted by Grace

You can do as I (and others ) have done and tuck the mounting tab under the plastic rather than over like the instructions have it.

Agree'd - mine is installed this way as well. My mech saw this potential immediately. Recommend!

motorknut · 06-17-2024, 12:02 PM

Quote:

Originally Posted by Grace

You can do as I (and others ) have done and tuck the mounting tab under the plastic rather than over like the instructions have it.

can't believe we didn't think of this! Thanks for the tip

06-16-2024, 10:46 PM	#1
motorknut Private 42 Rep 88 Posts Drives: BMW G87 M2 Join Date: Dec 2008 Location: at home iTrader: (0)	Zunsport oil cooler mesh - fitment hacks So I picked up the zunsport mesh for the underside, and a friend helped with the DIY. He pointed out that the mount bracket of the mesh doesn't sit flush with the OEM mount point on the car plate. he suggested getting some washers to make the bracket sit flush, and get an extended screw to replace the OEM 10mm hex bolt. (photo where he's pointing how the other hex bolts sit flush in the mount point, versus the one installed over the mesh bracket.) Anyone else considered some tweaks to the install? i'm a little concerned how sturdy it is with the original install instructions/parts as per Zunsport. Attached Images
	Appreciate 0 Tweet Quote

06-17-2024, 07:03 AM	#2
JABCAT Professor 4263 Rep 2,851 Posts Drives: '23 M2 & '22 X3 M Competition Join Date: Jun 2022 Location: Prosper, TX/Austin, TX iTrader: (0)	I've had mine installed for nearly 9k miles. The only change I made was a little bit larger screws for the rear. http://https://g87.bimmerpost.com/fo...+cooler+grille __________________ Her's: '22 X3 M Competition, Marina Bay Blue, Tartufo full Merino interior. His: '23 M2, Toronto Red Metallic, M highlight interior. '11 Callaway SC652 Carbon Edition Corvette Z06. Inferno Orange Metallic. 1 of 3. Last edited by JABCAT; 06-17-2024 at 07:16 AM..
	Appreciate 1 motorknut42.00 Quote

06-17-2024, 07:16 AM	#3
Grace Private 63 Rep 53 Posts Drives: G87 M2 on order Join Date: Jan 2023 Location: Australia iTrader: (0)	You can do as I (and others ) have done and tuck the mounting tab under the plastic rather than over like the instructions have it. Attached Images
	Appreciate 6 Ronin761441.50 LAGWAGN629.00 DSTR1450.00 LAnderson23280.00 motorknut42.00 CSBM52874.00 Quote