[ap2x]

Originally Posted by JCarrese74

So I have a 2023 M240i Xdrive with AA Catted downpipe, MST Cold air & JB4 with EWG hooked up. I ve been running Map 3 with 93 Octane and my question is how accurate is the Boost Gauge from the JB4 app. There have been multiple times I hit 30+ lbs of Boost, is the accurate?

Doubt that’s accurate. Limit of stock turbo is around 23 psi I believe

[mike@x-ph.com]

Originally Posted by JCarrese74

So I have a 2023 M240i Xdrive with AA Catted downpipe, MST Cold air & JB4 with EWG hooked up. I ve been running Map 3 with 93 Octane and my question is how accurate is the Boost Gauge from the JB4 app. There have been multiple times I hit 30+ lbs of Boost, is the accurate?

I recommend doing a proper datalog for accurate numbers

[JCarrese74]

That was off my data log

[Stanim]

Originally Posted by mike@x-ph.com

I recommend doing a proper datalog for accurate numbers

Mike, any sale events on Black Friday/Thanksgiving time on JB+/JB4?

[mike@x-ph.com]

Originally Posted by Stanim

Mike, any sale events on Black Friday/Thanksgiving time on JB+/JB4?

My phone number is in my signature

[mike@x-ph.com]

Originally Posted by 21M235IXGC

Hey Ex3ell ,,,,,,


Which map have you found best works on the m240i . I’m completely stock with just 93 octane .

• Map 1 didn’t seem to give that much of a boost , was either thinking of map 2 or switching to the absolute map 4 .

Read in the JB forums somethat says these G series b58’s run better on absolute maps than additives. Thoughts or comments ?,,

G chassis cars run high boost from stock, running an absolute map is safer and will get you more consistent results.

If you run an additive map, and the car is already targetting high boost, the DME might drop the timing ignition which will reduce the power

[mike@x-ph.com]

Originally Posted by 21M235IXGC

i ran a couple logs on map 0 and map1 on 3rd .. it seems to peak at 14 psi on map 0 and 16.9 psi on map 1 timing is aroun at 9-10* on both map 0 and map 1 .

i can send upload the logs if u wouldnt mind checking them out .

map 1 is +3 PSI
your results are on point

You can also check your datalog and it will show you what is the stock boost on this run and your Jb4 boost. if you have map 1 selected , the difference will be exactly 3 PSI (except during the spool period)

[mike@x-ph.com]

Originally Posted by 21M235IXGC

Thanks for your reply Mike . Yes your exactly correct map 1 is adding approx 3psi max to stock boost . my car apparently runs lower boost but higher timing as other data logs I’ve seen shows much higher boost than just 17psi but ofcouse they don’t have 9* of timing like I do , that being said is it still ok to run map 4 . Cus I know map 4 absolute is 20psi and that’s another 3 psi higher than what I run on map 1 and approx 6 psi higher than what my oem map 0 seems to run .

Just checking with ya u think that is ok . I only run shell 93 octane .

THank u

i recommend checking with BMS directly

[bam_bam_la]

I assume our onboard boost readings in the Sports Display is pretty accurate right?

I run 91 octane (all we get here in Cali from the pump) and have my JB+ installed. I dont think I ever see that I pull more than about 17 or 18 PSI under hard acceleration anywhere in the rev range.

[mike@x-ph.com]

Originally Posted by bam_bam_la

I assume our onboard boost readings in the Sports Display is pretty accurate right?

I run 91 octane (all we get here in Cali from the pump) and have my JB+ installed. I dont think I ever see that I pull more than about 17 or 18 PSI under hard acceleration anywhere in the rev range.

the gauges are not accurate, they show you stock boost

keep in mind, piggybacks operate by tricking the ECU into thinking thats its running stock boost

[bam_bam_la]

Originally Posted by mike@x-ph.com

the gauges are not accurate, they show you stock boost

keep in mind, piggybacks operate by tricking the ECU into thinking thats its running stock boost

Mike, you're a legend. Thats why I buy all my stuff from you!

So if I am on the default JB+ setting where they say its about 4psi additional, if the onboard is showing 15 pounds its likely closer to 19 pounds?

[mike@x-ph.com]

Originally Posted by bam_bam_la

Mike, you're a legend. Thats why I buy all my stuff from you!

So if I am on the default JB+ setting where they say its about 4psi additional, if the onboard is showing 15 pounds its likely closer to 19 pounds?

thank you

Yes you are approximately pushing 4 PSI on top of the stock boost reflected by the gauges

[MrJDS]

Mike, (or anyone else who wants to chime in) whats your opinion on using octane boosters or race gas concentrate to get to 95-100 octane range??? been using those to get to around 97 oct and running map 2 on my jb4 for my g87.

the 91 here in Nevada is so bad that I prob wouldn't feel comfortable running map 1 on it and you need stab insurance for all the race gas pumps here in vegas.

its prob best to just run e30 and run map 2 or map 4 im guessing tho?

[mike@x-ph.com]

Originally Posted by MrJDS

Mike, (or anyone else who wants to chime in) whats your opinion on using octane boosters or race gas concentrate to get to 95-100 octane range??? been using those to get to around 97 oct and running map 2 on my jb4 for my g87.

the 91 here in Nevada is so bad that I prob wouldn't feel comfortable running map 1 on it and you need stab insurance for all the race gas pumps here in vegas.

its prob best to just run e30 and run map 2 or map 4 im guessing tho?

Its best to run E30, use the Arco/rebel gas station on Jones & Tropicana

Race gas is excellent but very expensive

I have never used octane booster but from what i head they can be a little inconsistent

[nikman011]

If I am a ‘24 m240ix, G42/B58TU, in Pennsylvania, is there any reason to get the CARB APPROVED JB4, over the regular one?

[mike@x-ph.com]

Originally Posted by nikman011

If I am a ‘24 m240ix, G42/B58TU, in Pennsylvania, is there any reason to get the CARB APPROVED JB4, over the regular one?

if you are outside of Carb territory , no need to get the Carb JB4